InspectionPro   llc

  Professional. Foundation to Roof

And now by air


Blog

Gutter Maintenance and Repair

Posted on February 23, 2014 at 6:30 PM

Hello Friends,

With the weather so nice this weekend I wanted to share some home maintenance ideas. I am starting today with gutters. Remember safety first~

Call Andy for all your home inspection,home maintenance and improvement needs.

 

Gutter Cleaning and Maintenance

 

                                                                    PREPARING TO WORK ON YOUR GUTTERS

 

Thoroughly cleaning your home’s gutters every spring and fall will keep them working like they should. Leaves can build up and clog the downspouts, which can cause water damage to your roof and fascia (the board behind the gutter). Water pouring over the gutters or from leaks can end up next to your home’s foundation, in the basement or crawlspace.

 

                                                                                      GUTTER SAFETY

Cleaning or attempting to repair your gutters from on top of the roof is not recommended. Clean your gutters while standing firmly on a ladder. Avoid standing on the top three rungs and don't reach past the side rail – no farther than your belt buckle. When working from a ladder, use one bucket for gutter debris and another for carrying tools. Use wire hooks to attach the buckets to the ladder. Make sure the area below the gutter is clear.

 

                                                                                  CLEANING GUTTERS

 A hose-end attachment specially designed for gutters may make this project a lot easier. If you need to clean from a ladder, follow these steps.

Step 1

Begin cleaning the gutter near a downspout.

Step 2

Remove the large debris (leaves, twigs, etc.) with a trowel and dump it in a bucket.

Step 3

To clean out finer materials, flush the gutter lengths with a hose starting at the end opposite the downspout. Alternatively, you can use a gutter-cleaning attachment on a hose. If the water doesn’t drain, recheck the downspout strainer and clean as necessary.

If gutter water still doesn’t drain, the downspout may be clogged.

Check the drain end. If the downspout runs underground, remove it from the pipe as needed.

Install a small nozzle on the hose, and lock it at full pressure. Turn on the water and feed the hose up from the bottom of the spout. If this doesn’t clear the downspout or the nozzle is too big, use a plumber’s snake tool to clear the blockage.

Reattach the downspout.

Flush the entire gutter again.

Be sure to clean the downspout strainers.

                                                                   

                                                                      GUTTER MAINTENANCE AND REPAIR

 

Step 1

If there's still standing water after the gutter has been flushed, the gutter may not be sloped correctly and will require adjustment. The length of the system should decline at least ¼ inch every 10 feet toward the downspout.

If the gutter doesn’t slope enough, detach the hangers and adjust the gutter enough to drain properly, then reattach. It may be easier to work on small sections at a time to prevent the entire gutter system from falling.

 

Step 2

Inspect the gutter sections and downspouts for obvious damage and missing parts. Support hangers should be spaced every 2 feet along the gutter.

To replace or add hangers:

Install screw and ferrule hangers by marking their position on the gutter, drilling the holes in the gutter lip and fascia, then driving the screw with a drill through the ferrule.

Install screw-in or hidden hangers following the manufacturer’s directions. Most are attached through the rear of the gutter and into the fascia board, then clipped to the inside-front of the gutter.

If no fascia board exists, use roof hangers with straps, following the package instructions. Typical installation involves attaching a hanger across the gutter channel, clipping a strap to the hanger, then attaching the hanger under the shingles.

 

Step 3

Repair any leaks in the gutter.

To repair leaks at the seams, make sure the gutter lengths are tight against each other, and run a bead of gutter sealant on both sides of all joints.

To repair leaks at the end caps, add sealant along the inside of the joint.

To repair holes in the gutter material, ask a Lowe’s associate for products designed to repair aluminum or fiberglass gutters.

Identify gutter leaks by filling the gutter with water, but make sure the gutters have dried before repairing.

Step 4

Apply gutter touch-up paint to cover any blemishes as desired. If necessary, repaint some or all of the gutters.

                                                                              FOR ALL MY DIYers OUT THERE

                                                                                                     THE QUICK FIX

Make gutter cleaning easier--and safer (no ladder required)--with a long spray wand made from a 1/2-in.-diameter by 10-ft.-long PVC pipe. Cut two 6-in. lengths of pipe. Then use PVC cement to join these short sections and two 90-degree elbows with what is now a 9-ft.-long pipe, forming a J-shaped hook. At the short end of the hook, glue on a solid endcap. Drill three 1/8-in.- diameter holes in the cap. Glue a threaded adapter onto the opposite end of the pipe and attach a garden hose. Place the short end of the J-shaped hook inside the gutter and turn on the hose. As you walk along the house, high-pressure streams of water will rinse the gutter clean.

 

 

Categories: None

Post a Comment

Oops!

Oops, you forgot something.

Oops!

The words you entered did not match the given text. Please try again.

1 Comment

Reply alex leon
3:00 AM on February 8, 2018 
I will keep in mind all the useful information regarding gutter safety and its repair and implement it when the repair was needed.
https://plus.google.com/100469070036244973851